[China Glass Net] Cars should pay attention to the details when filming, because the details determine the role of car film. However, many car owners will ignore certain details when filming. The following details are often overlooked by others, so that the film process can be supervised during filming, and the problems that the builder misses are pointed out to ensure the success rate of the film and prevent the trouble of re-sticking!
1. Work clothes, chair covers or objects: Unpacking the insulation paper is clear that some static electricity will occur, and the fur of clothes or chair covers (wool, rabbit fur, fox fur or cotton wool) will be electrostatically absorbed onto the paper. Therefore, do not approach the above objects when disassembling the paper to avoid the fur on the object and the dust being absorbed by the static electricity.
2, the wind speed is too large: summer is the peak season of heat insulation, in the sun or the temperature inside the car is high, it is inevitable to open the cool air sticker in the car, but the wind speed can be reduced to lower when the paper is opened. After the paper is to be dismantled, put on the cellophane and then open the wind speed to avoid the dust in the car.
3. When someone unpacks the paper, someone closes the door: when the glass is washed or when the paper is opened, people can't switch the door. Sometimes, when the door is opened, it will form a rapid flow of air to bring in a lot of dust or sand.
4. The bottom of the sprinkler is unclean: when using the sprinkler, it is mostly placed on the ground, on the mat or on the seat cover. The bottom is usually unclean. When you open the paper, or the sprinkler sways above the paper, the bottom sand Grains and small stones will fall on the paper. When we use the sprinkler, we will clean the bottom.
5, film water: more than 70% of the construction workers directly use tap water, not through the filtration or deposition is not correct, because there are many impurities or sand in the water pipe, the water used in the sticker must be filtered or deposited.
6, hand pinch some: After opening the clear paper, it is necessary to pinch the heat insulation paper with two fingers, some of the hand pinch will have fingerprints and sand, the trick is to control the paper as a criterion, try to pinch a little less.
7, the method of wiping the water is not correct: there is a fixed method when wiping the glass to clean the glass, or scraping the water at random, or when the water is wiped off or not knowing the end will bring sand.
8. Flushing: The side or bottom wiper cannot be reached completely, and it is necessary to flush. When using the toilet paper, you should pay attention to the use of degreased toilet paper to prevent dust. Old cars or triangular windows should pay more attention to flushing, but the top can't flush, avoiding the dirt falling with water.
9. Dust: Many solar film sites do not have a closed room. Some people have stickers on the roadside or in the building. The large cars are whistling and raising a lot of dust. The larger winds also have a lot of dust. Therefore, if there are no closed room conditions, all the doors must be closed. Post it again.
10. Don't open it again: If the paper is attached to the glass, try not to pick it up again. The more the number of pick-ups, the more sand dust particles.
11. Pay attention to the objects inside the car: After removing the paper and spraying the water, the glass sticker sometimes gets like a watchboard, a steering wheel, a rear view mirror, a chair cover, a glass frame or a canopy, an audio, etc., and it will be stained with dirt.
12, the paper appearance is not clear: our cut paper is often placed on the car's foot pad, on the chair cover, or placed on the roof, engine, forming the table is not clean, but also attached to the appearance when the paper is opened due to static electricity . Therefore, when the clarified paper is not unpacked, it is necessary to wash or spray some water on the outside to protect the Egyptian sand.
13. Do not move a lot of positions: After removing the paper and spraying the water, it is not easy to be accurate when it is attached to the glass. If it is posted, it will find a lot of difference in orientation. Then it will be stained with objects near the glass or sand in the rubber and mud tank. .
14. The air is pumped into the sand: There are many invisible sand dust hidden in the mud tank rubber near the old car. After the paper is pasted, some glass is big, and there will be air with a water-pointed triangle. If the water is not fast at the moment, Driven out, the sand will continue to be sucked into the triangle.
15. Glass cleaning is not clean: Some old cars are old and new, and the attached ash should be cleaned. All labels and dirt should be cleaned up, otherwise the technology will not help.
16, the direction of catching water: just posted, the next action is to catch water, water can be driven from top to bottom, from right to left or from left to right, but not many water from the bottom up, avoid water to The downflow drives the sand down.
17. Pushing water: The final action of the sticker is to push the water. Usually 80% of the operators can't push more water. If it is slow in the winter, it usually does not dry for one month. Let's wash the removed plain paper. Later, it will be attached to the sun paper on the glass. The water is squeezed out by the copper plate. This method not only does not scratch or scrape the paper, but also can make the sand on the paper from large to small, from small to no, and squeeze the sand into the glue of the heat insulation paper. You can swing the door in two days.
Cosplay Women'S Clothes,Cosplay Costumes Captain Marvel,Cosplay Costume Hela Anime,Cleopatra Anime Clothes
Shaoxing Jinshengtai Textile Co. Ltd , https://www.sxheptex.com